In our, last post, we covered the basics of fabricating things from metal. One of our visiting hackerspace guests, Travis, is building a set of hexagonal columns. This week, I thought I'd add a few more things about measuring, layout and doing accurate welding work.
Once you've cut everything out as accurately as possible (see Part 1
), you need to lay out your work on a flat surface. Here Travis is using a 10mm steel plate, but anything flat (even a concrete floor) is preferable to trying to do it "by eye."
Professional fabrication shops will often have a ground flat cast iron table. It's worth looking our for old machinery being scrapped, as an old planer or milling machine bed can make a fantastic layout table.
Note the use of magnets - you can get 30, 45 and 90 degree magnets to make fit-up easier. For precision work, you will still need to measure the joints, but this makes things much easier.
After the parts are laid out, we tack weld every other joint.
A good process for welding a square, hexagon, or other geometric shape is to alternate tacking the outside and inside corners, and check the work frequently.
When we've got the basic shape tacked up, we measure all of the diagonals to really make sure it's straight. It's surprising how the initial layout can be off by 1/8" or more, even though it looks perfect to the eye. A straight edge across the diagonals doesn't lie.
A pipe clamp makes it easy to straighten out any diagonals that are too long by squeezing them down. The errors magically equalize and disappear. You'll probably need to squeeze your joints down a little more than they need to account for spring-back of the metal.
As we get farther along, it's important to keep the whole assembly from warping or getting out of flat. Restraining the parts in at least two places prevents this. Here we are using a standard 'C' clamp on the right and a fancy welding clamp on the left.
Some more detail of TIG welding a corner up. The TIG torch should be held at about 15 degrees from vertical and the filler rod (if used) should be fed into the shielded puddle from the side. Keep the welding time short to minimize warpage at each joint.
As the assembly starts to take shape, you'll need to think in 3 dimensions. Here, Travis has measured out and drawn a chalk outline on the layout surface. This lets him position both the of the hexagons parallel to each other and not rotated or shifted with respect to one another. The center of each leg of the hexagon has also been marked with a scribe, as has the center of each vertical support. Lining up the marks and tacking with the hexes clamped down will assure an accurate fit-up.
This all seems like a real pain in the rear, but you will thank yourself later, when everything has been covered with hundreds of inches of weld beads and you realize that all of those little errors add up.
Coming soon: part 3.
How amazingly you noticed the micro changes and wrote them in a broader way. You are really a creative mind who writes very impressively.ReplyDelete
lapping and polishing services
I am very happy to read this post because you have write amazing and describe point to point clearly about metal fabrication basic part2.ReplyDelete
Thanks for sharing blog post for metal fabrication basics part, i think this post should be helpful to everyone.ReplyDelete
I really liked the way you highlighted some really important and significant points. Thanks so much, I appreciate your work.ReplyDelete
contract lapping services
Bloggers like you are very few on World Wide Web and I am happy to found you. It’s like finding a pearl in the sea, tough but fruitful. Best wishes and regards.ReplyDelete
Flat lapping services
you write very well this article, i got good information after read your effective writing style. i hope you will continue this good work. Cast IronReplyDelete
Your blog is very useful and provides tremendous facts. Keep up the good work.ReplyDelete
fused silica substrate
Great information. Thanks for providing us such useful information. Keep up the good work and continue providing us more quality information from time to time.ReplyDelete
Polishing irregular surfaces
Also, for your home rebuilding, endeavor to set up some junk canisters, convenient can, and construction fence for better development. Furthermore, prepare for substantial effects which are conveyed now. granite countertops Leawood ksReplyDelete
It is truly a nice and helpful piece of information. I am glad that you just shared this useful information with us. Please keep us informed like this. Thanks for sharing. Metal Working MachineryReplyDelete
Can lights are "vitality pigs" since they cut vast gaps in your protection, and utilize wasteful glowing lighting (generally 75 watt). instant pot vivaReplyDelete
If there has any sharped corner of your products then you must be careful about those as the measuring and Welding Pro those corner is so much important to make it more perfect there.ReplyDelete
Thank you so much for sharing this blog with us. It provides a collection of useful information. You obviously put a lot of effort into it.ReplyDelete
Polishing irregular surfaces
Oh wow 10 Best Tig Welder 2020 worked.. thnx! I thought it was a scam and it would not work but it did so thank you!ReplyDelete
I’d like to thank you for writing on this topic. The information you provided was very useful. I will visit again in the near future.ReplyDelete
Without a shielding gas you will burn the Tungsten, contaminate the weld, and won't get any penetration into the work piece. ... The process for TIG welding and ARC welding is VERY similar where you have a lead with a electrode holder or “torch”.ReplyDelete
Some metal multi sort compartments are keenly structured with inward opening dividers to help dispose of cross-pollution, keeping your deliberately gathered recyclables significant.ReplyDelete
Abbotsford Chain link Fencing
I just couldn"t leave your site before letting you know that I genuinely delighted in the top quality information you present to your guests? Will be back again every now and again to determine the status of new posts.https://thetigwelder.com/best-tig-welder-under-2000/ReplyDelete
Can I recently say such a relief to find somebody that truly knows what theyre referring to on-line. You certainly have learned to bring a concern to light making it essential. The diet have to ought to see this and appreciate this side on the story. I cant think youre less common because you certainly have the gift. https://royalcbd.com/product/cbd-oil-250mg/ReplyDelete
The issues you’ve raised in this blog are very real. People usually hesitate to write on such topics but you did wonderful work. Keep it up!ReplyDelete
contract lapping services
I am thankful to you because your article is very helpful for me to carry on with my research in same area. Your quoted examples are very much relevant to my research field.ReplyDelete
wind tunnel polishing services
You should try out the Miller multimatic 215. It is giving the best welding services for certain works. Welding is better way for joining to steel than any other method. But you have to be well trained before starting professional welding worker.ReplyDelete
With a three-dimensional model, you can then come up with more probable conclusions. You no longer have to grapple in the dark or do different cross examinations just to finalize your decision. 3d laser scanning survey SydneyReplyDelete